Mobile Gas Flare S – 402280
We have developed the Mobile Gas Flare S especially for the low and medium pressure range.
It is a cost-effective and compact solution which is solely used for gas flaring applications. The device is ready for use in a few minutes and is thus a suitable measure to avoid large venting and purging emissions even in the area of service lines. Especially in the case of service lines, the volumes to be saved from a single service line are small, but as soon as these small quantities of such a measure are added up over many applications, e.g. in an annual balance, a considerable emission avoidance potential is created. With the help of the Mobile Gas Flare S, a significant contribution to the reduction of methane emissions in gas distribution networks can be achieved during the commissioning of service lines by using low investment costs and low labour costs per measure.
An integrated (continuous) ignition guarantees stable combustion and also ensures sufficient occupational safety, as no personnel have to go near the escaping gas to ignite the flame. The working range of the gas flare is limited to a maximum of 1 bar, as factors such as flame pattern, sound level and stable combustion would no longer be optimal at higher pressures. However, the inlet pressure may be up to approx. 10 bar and is then limited to a maximum of 1 bar by the connection accessories supplied with the gas flare. This means that the Mobile Gas Flare S can also be used in high-pressure range.
Flaring not only contributes to environmental protection by reduction of greenhouse gases, but also to occupational safety. With our Mobile Gas Flare S, we make a further contribution to climate-neutral distribution grid operation and provide technical solutions for climate protection and occupational safety.
- Compact and quickly ready for use
- Suitable for service lines and small volumes in low- and medium-pressure applications
- Clean, low-pollution combustion
- Integrated flame arrestor for safe operation
- Piezo igniter for automatic and safe flame ignition
- Can be combined with other measures to reduce methane emissions, e.g. flaring of residual gas volumes after usage of mobile compressors
- Pressure limitation to 1 bar: defined, safe working range
- High-quality workmanship, mainly stainless steel and brass
- Complete with connection accessories available in a case, consisting of: Hoses, connection unit with ball valve, pressure gauge and connections for concentration and pressure measurement as well as various adapters.
For safe operation of the Mobile Gas Flare S(1) it is necessary to use the appropriate accessories.
The Mobile Gas Flare S is connected to the connection strip(3) via a gas-resistant hose (material NBR)(2) with a length of 2 metres using quick connectors (Camlock). On the connection strip, which functions as a control panel, is a pressure reducer on the input side, which ensures that a maximum pressure of 1 bar is applied to the Mobile Gas Flare. On the outlet side, there is a ball valve with which the gas flow can be initiated from a safe distance to the gas flare. If required, two additional connections can be used to record and measure variables such as pressure with our smart memo or gas concentration with our OLLI. An integrated control manometer serves as a safety feature.
A gas-resistant hose(4) with a length of 5 metres can be used to connect the connection strip to the gas line or the house connection. The hoses are each equipped with a Camlock male part and a Camlock female part, so that they can be extended with another hose if necessary. Suitable adapters for connecting the hose to the gas pipe or the house connection are also available, usually the HUGO test head or the HEINZ test head(5) are also a suitable choice. All required accessories can be found in the accessories case(6). If you need further adapters, please contact your Esders representative.
Example: Start pressure 1 bar, total pipe volume 2 m3
Final pressure 50 mbar
Expected duration: min. 30 minutes
|Max. volume flow||approx. 8 Nm3/h at 1 bar|
|Max. pressure flare inlet||1 bar|
|Max. pressure accesory||10 bar|
|Flare ignition-type||piezo spark igniter with manual or permanent ignition|
|Power supply piezo igniter||battery-powered, 1x battery Mignon AA|
|Max. ignition duration||max. 8 h permanent ignition per AA-battery|
|Flaring approved for gases of explosion group||natural gas, propane, hydrogen|
|Flame arrestor approved for explosion groups||IIA, IIA1, IIB, IIC|
|Dimensions||height 685 mm, diameter set-up area 490 mm|